Hey guys so today I’m going to be showing you how I made these super awesome hand and ring chains I think they’re really easy to make and I think they’d be really awesome to wear to festivals and other type of events that you may be getting up to this summer I actually made a bunch of these and loads.
Of different designs but in this video I’m only going to.
Show you how I made these two designs so keep on watching and let’s get started so for this you’re going to need a couple of jump rings and hooks chains.
Pins and of course you can use old pieces of jewelry and just recycle them you’re also going to need a pair of pliers and any type of round shaped object that’s kind of long and stick like I’m just using the dotting tool you can use a.
Pencil or something else like.
That and of course tweezers as well so I’m going to be showing you how I made this white pearl one first and this was actually the easiest one to make so the first thing you have to do is.
Chain and measure it around your middle finger make sure it’s not too tight and not too loose and then just cut it off with your pliers or scissors then just take an open jump ring and put both ends of the chain through the jump ring and close it up with a pair of tweezers now you’ve made the ring pot the next thing you have to do is take the eye pin and thread the Pearl bead through it then just bend the eye pin back a little bit and make sure there’s not a.
For the bee to move around in then just take your dotting tool or pencil and.
Use it to shape the eye pin to make a hook type shape it’s.
Kind of hard to explain but.
All you have to do is just bend it back over itself take your pliers and cut off the extra bit of the pin.
Use the pliers to just close up the hook you just need.
To make four or five of these depending on the length of your hand and then just attach them together.
Once you’ve attached all of them together it should look something like this take one end of this and attach it to the jump ring though you touch to do chain before use your tweezers to just close everything up so far it should look something like this and we’re almost finished just one more step.
Left last thing to do is to make the bracelet part so take the chain and measure it around your wrist make sure it’s pretty tight and not too loose as we’re going to add the hooks and the jump rings cut off the excess chain using the pliers apply one jump ring to both ends.
Of the tune but only apply one hook to one end use your tweezers to make sure everything’s securely closed so it should look like this now so the last thing to do now is to attach a jump ring to the middle of the chain and then attach it to the rest of the bracelet use your tweezers to close it up and.
Then make sure everything else is closed up properly as well once.
You’re done it should look something like this so now I’m going to show you how I made this other one so for this you do the same thing as before.
To make the ring pop measure it around your middle finger and cut off the excess chain thread both ends of the chain through a jump ring I used the same method as I showed before to make this green beaded ITIN so I thought it’d that through the jump ring as well making sure it wasn’t in between the two chains then I just closed up my jump ring with a pair of tweezers and it should look something like this.
I already attached another jump ring to the other end of the eye pin then I threaded one end of the.
Chain through the jump rings as.
You can see it took ages to do because it was one of those twisty jump rings I do not recommend these just use the other type of ones they’re much more balanced once you’re done it should look something like this measure the chain down to your wrist and cut off the excess.
So I already measured out a piece of chain around my wrist and the touch jump rings and a hook to it then I attached a jump ring to the bottom of the chain that I already cut out before and to the middle of the bracelet once you close up the jump ring it should.
Look something like this so far after that take the chain and measure it from the bead to the bottom of bracelet it should form a triangle type of shape then just cut it often attached it together do this to both sides and.
You have finished so once you’re done it should look something like this I really hope you enjoyed watching this really cool DIY I actually made a bunch of other designs as well to give to my friends and stuff so if you want.
Me to make a separate video on that please leave me a comment down below and like this video and I shall.
Get onto them as for now thank you so much for watching I really hope you enjoyed this video and I’ll see you soon bye.